Mustang BBK Cold Air Intake & Throttle Body Installation (94-95)

Posted 7/2/2014 by Jeff Jimenez

Mustang BBK Cold Air Intake & Throttle Body Installation (94-95)

FOLLOW: mustang , 94 04 mustang , sn95 mustang , video , installation , bbk , intake , air fuel

Adding 20+ horsepower to you 5.0L SN-95 Mustang is simple thanks to BBK Performance Parts. They offer a great selection of intake products for your 94-95 5.0L Mustang. Follow along in the video as we show you just how easy it is to install a new BBK cold air intake and throttle body.

BBK designs and manufactures all of their Mustang performance parts right here in the USA. For the 94-95 Mustang GTs, they offer intake options such as cold air intakes, throttle bodies and even high flow mass air meters. Each mass meter is calibrated specifically for your Mustang and its fuel injector size. Lastly, don’t forget to check out the BBK header and mid-pipe options available for your SN95 Mustang. BBK offers both long tune and shorty style headers for your 5.0 Mustang.

Shop our complete line of BBK parts here: BBK Mustang Parts.


Comments


 


 


About the Video

Mustang BBK Cold Air Intake & Throttle Body Install (94-95 5.0L)

Check out our YouTube channel for even more tech tips, installation videos, how-tos, and more. The best place to go for anything Mustang related!

Published on 2014-06-27
Freeing up some horsepower on your 5.0L 94-95 Mustang has never been easier thanks to BBK Performance Parts. Their fenderwell mounted cold air intake will help you pull cooler air from outside the engine compartment. When you combine the BBK Cold Air Intake with one of their larger throttle bodies you will greatly maximize your performance.

Watch in this video as the guys over at BBK show us just how easy it is install their cold air intake and throttle body. Installation can be done in your driveway with simple hand tools in less than 1 hour.

Be sure to click on the link above to shop our complete line of BBK performance parts for 5.0L SN-95 Mustangs!

LatemodelRestoration.com 50resto SVE
Transcript
Are you looking for an easy way to add an extra 20 or more horsepower to your '94 to '95 five liter Mustang? Well, you're in luck. BBK Performance has a wide selection of intake options for your five liter. Now these include their intake and throttle bodies.

Now the BBK cold air intake features a high flow air filter that is mounted inside the fender to help you pull cooler, denser air into your engine. The intake also includes chrome-plated piping, all needed installation hardware, and installation instructions to make that install go as smooth as possible.

Now, when you combine one of these intakes with one of BBK's Power Plus Series throttle bodies, you're definitely going to maximize your performance. These throttle bodies are available in a 65 millimeter, a 70 millimeter, and a 75 millimeter version to fit your application.

Now with all BBK Performance products, they are manufactured and designed right here in the United States, so you know you're getting a great quality part for your SN-95 Mustang.

Now if you'd like to see more of these BBK Performance videos, go on over to our You Tube channel, and make sure you subscribe to get these delivered directly to your inbox.

Now to shop more BBK Performance Parts, click on the link in this video, or simply head on over to LatemodelRestoration.com

Now let's let the guys at BBK Performance show you just how easy it is to install one of these intakes and throttle bodies on your Mustang.

To get started, unplug the mass air meter and inlet air temperature sensor harness from the master plug on the fender apron. Flip the latches on the air box, loosen the hose clamp at the throttle body, and disconnect the PCV hose from the oil filler neck.

Then lift the stock inlet air tube out of the car, and set it aside. To remove the throttle body, disconnect the helper spring, and the throttle and cruise control cables, from the linkage. Unplug the idle air control and throttle position sensors, then remove the four nuts that hold the throttle body to the intake manifold, and pull it away.

Completely remove the stock gasket and any remnants to ensure a good sealing surface for the new BBK throttle body. On a workbench remove the idle air controller and throttle position sensor. Place the supplied TPS spacer over the end of the throttle shaft, and bolt the TPS onto the BBK throttle body.

Be sure to line up the teeth inside the TPS with the throttle shaft when installing it. Then using the supplied gasket, bolt the idle air controller onto the BBK throttle body.

Back at the car, slip the supplied gasket and the BBK throttle body over the studs on the intake manifold, and tighten it down. Then reconnect the IAC, the TPS, the throttle and cruise control cables, and of course, the helper spring. Before wrapping up the throttle body install, have a helper step on the gas pedal to verify that you can achieve full throttle.

Back on the cold air induction system, remove the bolt that holds the base in place, and pull it and the snorkel out of the fender well. Prepare the fender well plate with the supplied o-ring and studs, then work the inlet elbow into the o-ring. This is the most difficult part of the installation due to the tight fit of the tube inside the o-ring.

The next step is to remove the mass air meter from the air box base, by unclipping the sections of the base and unbolting the meter, once you have the base separated. Remove the screen from the meter and bolt the meter directly to the BBK inlet tube using the supplied hardware. Please note that there is no gasket required between the meter and the tube.

Now you can drop this assembly into place in the car and tighten it down with the original fender bolt and grommet. You'll need to pull the inlet air temperature sensor out of the stock intake hose and place it into the BBK tube using the supplied grommet.

Slip a blue coupler and two clamps over the ends of the inlet tube, then work the inlet tube into place. Tighten the clamps, and reconnect the PCV hose. Now extract the wiring harness from the stock air box base and connect it to the mass air meter, IAT sensor, then to the master plug.

To finish the installation you'll need to lay on the ground and place the filter up in front of the fender liner, behind the headlight, onto the end of the inlet tube where it's protruding into the fender well. We lifted the car and back lit it here to show you where it goes.

Now we can run the car on the Dyno and see how much power we picked up with these super easy and affordable bolt-ons.

[CAR ENGINE RUNNING]

Mustang BBK Cold Air Intake & Throttle Body Installation (94-95) Tech Info

Ford Mustang 5.0L GT & SVT Cobra - 1994 (94) - 1995 (95)