Black Friday Sale!

Fox Body Mustang LS1 Swap Parts & Overview

Posted 11/27/2013 by Jeff Jimenez

Watch as LatemodelResto employee Scotty walks you through his Fox Body Mustang LSx Engine swap. It isn't always the motor of choice for Ford enthusiast but the outcome was amazing!!

FOLLOW: mustang , 79 93 mustang , fox body , installation , tech , engine

Fox Body Mustang LS1 Swap Parts & Overview - fox body mustang ls1 engine swap

Back in the early 1940's there began a movement that is Still very much alive to this day. The quest for speed was an appetite that couldn't be quenched. No matter how fast you went you always looked for more ways to have "just a little more". The most popular platform to start with in that era were the Ford Model A's and Model T's. It was easy to understand why these cars were so popular. They were readily available and you could pick them up fora little of nothing.

The Hobby Really took off and went to the next level in the Late 50's. Chevrolet introduced the legendary Small block V8. True it wasn't the first V8 available but it made good power and proved to be somewhat more reliable than the earlier flathead motors. The Automotive aftermarket started producing speed parts and it was only a matter of time before the speed junkies realized that the Lightweight Model A was a perfect candidate for the well performing Small block Chevy. Immediately you have the die-hard Ford followers forming lynch mobs, but at the same time you had the hardcore racers looking to strap a seat to a bare frame just to make the "car" lighter. I tend to side with the 'rodder and have a broader perspective, looking to take great ideas and make them better.

Fox Body Mustang LS1 Swap Parts & Overview - mustang lsx engine swap

The quest for speed is still thriving and has been magnified to a whole new level. All out race cars in the day performed as well as a Mustang GT off the showroom floor. I too have been bitten by the "speed bug" and decided to build a car to feed my appetite. Like many beforehand I looked for a solid platform to start with which hands down would be the Fox body Mustang. There are tons of them out there, you can pick them up for practically nothing, there is a huge aftermarket following, plus in my mind they are just plain cool.

I found an 86 LX Coupe that was laid to rest in a field and picked it up for $250.00 It wasn't pretty but it was exactly what I wanted to start with. I have a special place in my heart for 4 eye cars, you either love them or hate them.I chose a 4 eye coupebecause #1 coupes are lighter and more sound than a hatchback, # the 4 eyes are lighter than the 87-93 cars. Keeping with the "Lighter is faster" theme I completely stripped the car down to begin the transformation.

Fox Body Mustang LS1 Swap Parts & Overview - fox body mustang ls1 swap project

Since its introduction in 1997 I have been researching the LS1 platform. They come from the factory in 97-08 Corvettes, 98-02 Camaros/Firebirds, and 99-08 GM Trucks/SUVs. Though each motor has its individual characteristics the core design remains relatively the same. So no matter what style you find the same result can be accomplished. Earlier this year GM performance parts released a front distributor drive conversion for their NASCAR LS motor. Since they can't use Coil packs they have to use a conventional distributor setup. The best part about it is they designed it based off of the Ford Distributor. That was the last straw... I knew I had to build one. I picked up a GM Crate motor locally from Greg May Chevrolet and began my LS1 transformation. After I un-crated the long block I pulled the Factory front cover off to install the Front mount distributor cover. While it was off I went ahead and took advantage of the situation and installed a "GTP series 4" cam which specs out at .568" lift and 232 duration on a 112 LSA. Needless to say the cam will really wake up the motor and move the little car down the 1320 pretty quickly. I've got more to come and should have some updated pics and info next week.

Udapte: Fox Body Mustang LSx Swap Part II

Well, it's time to update the progress I've made on the car. As you can see, after getting the car, I totally stripped it to a shell to do the bodywork and paint it. To me this is the only way to do a paint job. Yes it is time consuming but you don't have to worry about Tape lines or over spray on your trim items, really the only thing you have to worry about is remembering where everything goes when putting it back together.

Fox Body Mustang LS1 Swap Parts & Overview - fox body lsx engine swap

Not the best, but it was ok for my first paint job. I got it kind of thin in some places and it had some orange peel so after sanding it smooth again I had a painter friend that I work with re spray it for me. I then proceeded to re-assemble the nice new parts on it.

I wanted to keep this swap as simple as possible. Is it possible to bolt in aLS1 without major modifications? Answer yes, yes it is. Anthony Jones makes a Tubular K-Member for a LS1 to fit in a mustang. I bought that K-member AJE-and a set of Ceramic coated Kooks Headers " KOK-5512C "so at least the motor would bolt in with no problems. The next obstacle was which tranny I use. By far the easiest way to go is automatic....but it’s a whole lot more fun to row through the gears so I decided it would have to be manual tranny. That left me with 2 options. #1 I could fabricate a hydraulic setup out of a T-bird Turbo Coupe and adapt it to the GM 6 speed or #2 I could find a way to use a ford setup so it would bolt in as well. I found a Lakewood Bell housing that was designed for a Tremec TKO to bolt to a small block Chevy. Since the LSX motors share basically the same bell housing pattern as a small Chevy this would be the easiest bolt in application. I modified the bell housing to accept a 94-04 clutch fork by swapping the pivot stud to the other side of the bell housing and enlarging the clutch fork hole. Now this swap will function just like a standard 5.0 5spd and the beauty is that it could be changed back to FORD power in a matter of Hours.

Fox Body Mustang LS1 Swap Parts & Overview - fox body ls1 swap transmission

Now was the time we've all been waiting for...especially me......I set the motor in its new home. All went in fairly smoothly. While we did this we found two areas that needed to be addressed. The Engine and Tranny are a bolt in application but you have to use an aftermarket Cross member made specifically for a Tremec . Also the 94-04 Clutch Fork is a little longer than the 79-93 one so it hits the transmission tunnel. Nothing that a little clearance won't cure. Other than that it's easy to drop in and looks great.

Fox Body Mustang LS1 Swap Parts & Overview - mustang ls1 engine install
Fox Body Mustang LS1 Swap Parts & Overview - fox body ls1 motor swap


Udapte: Fox Body Mustang LSx Swap Part III

Well it's been a while since I've updated the progress so I'll bring you up to speed with where I'm at in the build. Since the last entry, I have started the long process of putting the car back together. I have installed the Roll Bar along with some of the interior panels so it is starting to feel like a car again instead of an empty shell. By the way this is our Cloth upholstry we offer for the 87-93 Sport seats

LS1 Fox Body Mustang Project

After we got that installed I took the car over to a buddy's shop to have the Rear Anti-Roll Bar welded in. It's designed to keep the car level when launching instead of one side "squatting" more than the other. UPR makes a really nice product and installation wasn't difficult.

While I was there I also had him relocate my Steering Rack. It wouldn't bolt up because it was hitting the oil pan. We welded in a piece of 1" square tubing to drop it down which was enough to do the trick. I still have to get a set of Offset Rack Bushings to get it exactly where I want it.

LS1 Fox Body Mustang Project

Here you can see the Crossmember I used to bolt up the transmission. It is specifically designed for the Tremec transmissions to bolt in the factory location on the Mustangs.

LS1 Fox Body Mustang Project

While I was there I also installed a Driveshaft Safety Loop as well since the car will see ALOT of Track time.

LS1 Fox Body Mustang Project

Another obstacle I had to overcome was the clutch setup. If you remember the clutch fork I used was a 94-04 unit so it was longer than the normal Fox body one, which in turn caused it to hit the floor pan. I had to clearance the floor pan to clear. This was done with a Precision instrument that is commonly referred to as a "sledge hammer". I'll go back in and do body work to it to make it look better and repaint this area.

>LS1 Fox Body Mustang Project

The second thing to address is the clutch cable mounting location. I'm going to enlarge an existing hole on the bell housing to allow the cable end to fit in it and us a factory retaining clip to hold it in place.

LS1 Fox Body Mustang Project

That pretty much gets the Underside of the car ready to go. When the car is ready to Drive I will install the Aluminum Driveshaft to finish out the driveline.

With the mechanical aspect of the build coming together I then turned my focus to the appearance. I started the process of restoring all of the factory trim that I had taken off the car in the beginning. It was all still in pretty good shape so all it needed was a thorough cleaning, scuffing, and a fresh coat of trim paint. After the paint dried I installed new door weatherstripping and reinstalled the parts.

LS1 Fox Body Mustang Project
LS1 Fox Body Mustang Project

Slowly but Surely it's coming along and hopefully in the near future I will have the final chapter in the build along with some video clips of it at the track

Udapte: Fox Body Mustang LSx Swap Part IV

Well, I know those who have been following the build have been wondering what kind of progress has been made. I've been hard at work finishing the little things that plague a project like this. Wiring gremlins, fuel system gremlins, as well as the weather not being as cooperative as it could have all slowed the build process.

Since the last installment I have done quite a bit of work. The steering rack has been moved and permanently attached. I had to lower it about an inch so it wouldn't hit the oil pan. The brakes are hooked up and bled, the headers are in place and I had to lengthen my steering shaft for proper clearance. Now that those items were taken care of all I had left to do is start putting parts on it. For ignition I used the MSD Pro-Billet distributor - part# MSD-8579 which is a simple plug in installation to the MSD Digital 6 ignition box - part# MSD-6520. I chose this box because it features a 2-step rev limiter, timing advance feature for nitrous or other power adder, as well as timing retard during start up. All those features were exactly what I was wanting for my application.

LS1 Mustang

Next I was able put my water pump on. In order to clear the bulge for the distributor I had my Dad build some custom spacers out of aluminum, "It sure is nice to have someone with his fabrication experience on my side". The Lower radiator hose is a KM1119 which is the factory replacement for a 5.0 Fox application. The upper was a little more tricky. The water pump inlet is relatively in the same position as the 5.0 but at a slightly different angle. Since I knew the basic shape I needed, the Local Parts supply store was kind enough to let me look through their entire inventory until I found what I needed. I know that it is a Dodge application but don't know the exact model it's for, all I know is it fit like a glove.

LS1 Mustang

To finish out the cooling system I went with a great radiator/fan Combo from SVE. The Radiator is a MUSTANG 5.0L SVE ALUMINUM RADIATOR for manual transmissions and is a 2 row polished aluminum unit that works as great as it looks. This also has the polished finish so it matches their radiator.

LS1 Mustang
LS1 Mustang

After I got the cooling system out of the way, it was time to put the finishing touches on so I could finally start it for the first time. I made the fuel lines out of braided steel line and A-N fittings and ordered a Demon 750 to satisfy the motors fuel cravings. I also decided that I was going to use Nitrous as my power adder so I ordered a fogger plate. As for the rest of the kit, I will be calling Nitrous Outlet for them to custom make the rest of my system.

LS1 Mustang
LS1 Mustang

Now the Moment we've all been waiting for "especially me" it's time to start it. AS I stated in previous post the Front mount distributor setup utilizes a Ford distributor application and the only difference between a 5.0 H.O. firing order and an LS based motor is that you swap #8 and #3. I used a set of red Ford Racing plug wiresand they fit just like they were meant to be there “granted I still have to loom them so they look better". The first attempt wasn't successful due to me installing the distributor 180 Degrees out and resulted in a huge back fire. After I got the distributor in the correct position it was a success. It busted of and idled flawlessly.

Be sure to check out the long awaited video of it running after I brought it home from the Exhaust shop. Hope you enjoy....I know I do. The next time you see it..... it will be in action and we'll see how much tire smoke we can make as well as some videos of it at the drag strip.

Udapte: Fox Body Mustang LSx Swap Part V

Well For those who have been following this build you know that I haven't posted in several weeks. The reason for that is I had sent the car to the paint shop to have the front clip finished and installed. It required more work than I was comfortable tackling myself so I had it professionally done. After patiently waiting I finally got it back and started putting all the trim back on it.

I built this car using all the parts we offer. The only aftermarket body panels are the Drivers and Passengerfenders, along with the Cervini's 2.5" Cowl Hood. Everything fit up really nice and there wasn't a lot of adjustments that had to be made for the gaps to align with each other.

1986 Ford Mustang w/ LS1

I also painted all the trim on the car the original grey color using our Exterior Trim Paint. The lights were the next thing that needed attention so I bought the 79-86 8 piece headlight kit to take care of the front and the 85-86 SVO rear tail lights "same as 93 COBRA" for the rear, since they matched the charcoal grey trim. In the next picture you can also see the antenna delete panel I installed since the car won't have a radio.

1986 Ford Mustang w/ LS1
1986 Ford Mustang w/ LS1

here are a couple of more pics that we took from different angles

1986 Ford Mustang w/ LS1
1986 Ford Mustang w/ LS1
1986 Ford Mustang w/ LS1

Here is one that we have put on our wallpaper page that you can download as well as several other Mustang pictures to choose from.

>1986 Ford Mustang w/ LS1

Next up is the Interior. I've been working on putting new interior pieces in as well as swapping some of the original panels from red to Black. I'll have pictures up shortly and the results are coming out very nice. Stay tuned.


Comments


 


 

Fox Body Mustang LS1 Swap Parts & Overview Tech Info

Ford Mustang - 1979 (79) - 1980 (80) - 1981 (81) - 1982 (82) - 1983 (83) - 1984 (84) - 1985 (85) - 1986 (86) - 1987 (87) - 1988 (88) - 1989 (89) - 1990 (90) - 1991 (91) - 1992 (92) - 1993 (93) - 1994 (94) - 1995 (95) - 1996 (96) - 1997 (97) - 1998 (98) - 1999 (99) - 2000 (00) - 2001 (01) - 2002 (02) - 2003 (03) - 2004 (04) - 2005 (05) - 2006 (06) - 2007 (07) - 2008 (08) - 2009 (09) - 2010 (10) - 2011 (11) - 2012 (12) - 2013 (13) - 2014 (14)