Easily free up some extra horsepower on your Fox Body Mustang with one of the SVE cold air intakes. Not only will you benefit from extra horsepower but you will also benefit from it not breaking the bank! These performance intakes include everything you need to finish off the installation. Installation only requires a few hand tools and can be done in your driveway!
If you want to maximize the performance of your intake system on your 5.0L Mustang, don’t forget to check out some of our popular power packages that feature the SVE Cold Air Intake along with other customer favorite SVE parts such as under drive pulley kits and 70mm throttle body. Click the link below to shop our full line of SVE performance packs!
The factory 75 amp alternator used in the 1986-1993 Mustang 5.0L was, to put it mildly, undersized. Add on something as simple as underdrive pullies or an electric cooling fan and you've effectively killed the ability of the alternator to keep the battery charged. Luckily, turn-key solutions like our SVE 130 Amp A... more
The Ignition system is one of the most overlooked & under-appreciated systems on a Fox Mustang. From the factory the stock system was quite capable & reliable. There are still many a fast Mustang out there running stock style distributors, wires, plugs, and coils; however, as with most systems, there is room for impr... more
Watch our 5.0L Mustang Ignition Coil Install Video! Improve spark performance & increase spark output voltage. Replace your old worn out factory ignition coil and replace it with a performance ignition coil. LatemodelRestoration.com carries Mustang ignition coils from manufacturers such as MSD, Performance Distributors... more
Why do you need to upgrade the starter on your 1979-1991 Mustang 5.0L? Well, there are actually a few reasons. First off, the way the 79-91 starter is wired, the fender apron mounted starter solenoid (or starter relay) carries the full current load of the starter. This causes the solenoid in these year ranges to fail... more
About the Video
Fox Body Mustang Cold Air Intake Installation (89-93 5.0 SVE)
Check out our YouTube channel for even more tech tips, installation videos, how-tos, and more. The best place to go for anything Mustang related!
Published on 2013-11-11 1989-93 FORD MUSTANG 5.0 SVE COLD AIR INTAKE KIT POLISHED - FOX BODY Brand: SVE Part Number # LRS-9659CA3K Fits: Ford Mustang 5.0L - 1989 (89) - 1990 (90) - 1991 (91) - 1992 (92) - 1993 (93)
Are you looking to increase horsepower and fuel economy on your Fox Body Mustang? How about doing all of this without breaking the bank? Well you are in luck! The SVE Cold Air Intake for the 89-93 5.0L Mustangs will do all of this and even improve the looks of your underhood with its polished finish. Installation is super easy with the help of this how to installation video!
Each SVE intake includes all the needed hardware and components you need to replace the restrictive factory intake tube and box with this high flow SVE CAI. Don't forget to look at our SVE Power Packages that include the SVE intake and under drive pulley kit, 70mm throttle body and many other SVE performance parts. They are guaranteed to wake up any 5.0L HO push rod motor!! See our complete line of SVE performance packages here: http://www.latemodelrestoration.com/products/Mustang-Performance-Parts-Kits-1979-1993Mustang Performance Part Kits
LatemodelRestoration.com, SVE & 5.0Resto are dedicated to the restoration and performance of your Project Foxbody Mustang!!
Transcript Improving the power output of your Fox Mustang 5.0 from '89 to '93 can be as economical and simple as installing one of our SVE cold air induction kits. Not only does it brighten up your underhood appearance, it improves your rear wheel horsepower. Installation takes mere minutes using common hand tools and is a direct replacement for your existing induction system. Follow along as we show you just how easy it is to install.
Unplug the mass air meter. Remove the two mass air bracket to strut tower bolts. Slide the mass air boot to air box clamp out of position. Loosen the air inlet tube clamp. Remove the mass air and inlet tube assembly from the vehicle.
Loosen the two clamps at the mass air and separate the mass air meter from the boot and tube. Remove the three bracket bolts from the bottom of the mass air. Remove the two air box retaining nuts. And then remove the air box from the car.
Remove the three air silencer retaining nuts. From underneath the fender, you can fully remove the air silencer from the car. Back up top, remove the two rubber insulators. Clean up the area if needed.
Slide the elbow tube through the fender plate and install the fender plate using the supplied hardware. Slide the boot with the lip in the middle of it on the end of the elbow tube. Slide two clamps into place.
Put the mass air in the boot. Slide the smaller boot on the other end of the mass air. Slide on two more clamps. Put on the remaining boot to the throttle body and two more clamps. Finally, install the inlet tube.
Making sure there's clearance at the strut tower and inlet tube, tighten all the clamps and reconnect the mass air meter. From underneath the fender, you can install the air filter onto the elbow tube and tighten the clamp.
See? That didn't take very long at all. You'll notice we did not use the bracket included with the kit. This is because, well, mainly my personal preference. I don't like putting them on, because sometimes it just makes things a lot more difficult. You can use yours if you desire. You can check out more SVE performance products for your Fox Mustang at latemodelrestoration.com.
This is by far the best experience I have ever had buying parts for my mustang. There is no other place for me, then LatemodelResto. I have bought multiple parts over multiple orders and have had nothing but a smile from ear to ear. Aaron Westerman was my contact person from LatemodelResto. I could not ask for a better customer service representative than him! He went above and beyond multiple times for me and made my experience with Latemodel the reason I keep coming back. LatemodelResto will continue being my #1 stop for my Mustang parts.
these are mine and my Dads 2015 GT's. My Dad owns 2 other Mustangs a 1990 notch back and a 88 GT convertible. he has owned 8 Mustangs over time and over 230 cars in his lifetime. from Ford Model A's...