July 4th Savings! * Use code MURICA15 *

Ford Racing 5.0L Aluminator Crate Engine Build

Posted 8/10/2013 by Jeff Jimenez

The Ford Racing Aluminator Crate Engines are the ultimate in hand built performance motors! Watch the video to learn more.

FOLLOW: mustang , 10 14 mustang , s197 , video , tech , ford racing , engine

Ford Racing 5.0L Aluminator Crate Engine Build - Ford Racing Aluminator Crate Engines

If your stock 5.0L Coyote Engine just won't cut it with your performance modifications, look no further than the Ford Racing Aluminator series engines. These hand built motors are covered by Ford Racing Performance Parts' (FRPP) 2/24 Warranty. That means you are covered by a 2 year 24,000 mile warranty.

The 5.0L Aluminator crate engines are available in three different versions to fit your racing application. The first one, M-6007-A50SC, is built for Mustangs with forced induction. It features lower compression and upgraded connecting rods to help handle higher boost levels from superchargers and turbos. The second version, M-6007-A50NA, is built for those looking to take their N/A bolt on Stang to the next level. With its upgraded internals, this N/A version is ready for bolt-on performance mods and nitrous kits. The last version, M-6007-A50XS, is the ultimate in 5.0L Coyote motors! It is a 500+ HP Naturally Aspirated motor that is begging for the track. It features upgraded internals, cams, and tons of parts borrowed for the Cobra Jet!

M-6007-A50SC 5.0L ALUMINATOR FOR SUPERCHARGED APPLICATIONS

  • Direct Replacement for 2011-2014 Mustangs
  • Built for Mustangs with Forced Induction: supercharger or turbo charger
  • 5.0L (302 cubic inches)
  • 9.5:1 low compression ratio (nominal)
  • Mahle Hard Anodized forged pistons with Graphal low friction coating
  • Manley H-beam connecting rods with ARP bolts
  • Lightweight aluminum cylinder block, part no: M-6010-A50L4V, features cross-bolted main bearing caps and thick main bearing bulkheads for bottom-end strength
  • Optimized oil drainback and windage control improve high-RPM performance
  • Large sump oil pan with 8qt capacity
  • Includes manual transmission engine harness and flywheel
  • Vehicle harness and PCM not included
  • Includes machined front cover for Ford Racing Supercharger FEAD system
  • Features colder, heat range 0 spark plugs for supercharging, part no: M-12405-M50
  • Includes Ford Racing oil filter, part no: M-6731-FL820
  • Use our NEW wiring, PCM and installation kit M-6017-A504V designed for street rod/project car installation.
  • Does not include alternator, for alternator kit see M-8600-M50ALT
  • Remote Mount Filter Adapter M-6881-M50 available for applications requiring oil filter relocation
  • Engine mount bosses and bellhousing mount pattern common to 4.6L modular engines.
  • NOTE: Due to 9.5:1 compression ratio, custom tuning is required for optimum performance
  • Includes M-9680-M50 5.0L Mustang engine cover kit

M-6007-A50NA 5.0L ALUMINATOR FOR N/A APPLICATIONS

  • Fits 2011-2014 Mustang GT
  • 5.0L (302 cubic inches)
  • 11:1 compression ratio (nominal)
  • Mahle Hard Anodized forged pistons with Graphal low friction coating
  • Manley H-beam connecting rods with ARP 2000 bolts
  • Lightweight aluminum cylinder block, part no: M-6010-A50L4V, features cross-bolted main bearing caps and thick main bearing bulkheads for bottom-end strength
  • Optimized oil drainback and windage control improve high-rpm performance
  • Large sump oil pan with 8qt capacity
  • Includes manual transmission engine harness and flywheel
  • Vehicle harness and PCM not included
  • Includes machined front cover for Ford Racing Supercharger FEAD system
  • Features colder, heat range 0 spark plugs for supercharging, part no: M-12405-M50
  • Includes Ford Racing oil filter, part no: M-6731-FL820
  • Use our NEW wiring, PCM and installation kit M-6017-A504V designed for street rod/project car installation.
  • Does not include alternator, for alternator kit see M-8600-M50ALT
  • Remote Mount Filter Adapter M-6881-M50 available for applications requiring oil filter relocation
  • Engine mount bosses and bellhousing mount pattern common to 4.6L modular engines.
  • Includes M-9680-M50 5.0L Mustang engine cover kit

M-6007-A50XS 5.0L ALUMINATOR XS

  • Fits 2011-2014 Mustang GT
  • 500+ Horsepower
  • 5.0L - 302 cubic inches
  • 11.0:1 compression ratio
  • Mahle hard anodized forged pistons with Graphal low friction coating
  • Manley H-beam connecting rods with ARP2000 bolts
  • Lightweight aluminum cylinder block features cross-bolted main bearing caps and thick main bearing bulkheads for bottom-end strength
  • Ford Racing Camshafts
  • M-6550-M50BINT intake camshaft - 13mm lift / 263 degrees duration
  • M-6550-M50BEXH exhaust camshaft - 13mm lift / 290 degrees duration
  • Ford Racing M-6675-M50BR 12 quart rear sump oil pan features optimized oil drainback and windage tray to control oil and improve high-rpm performance
  • Ford Racing M-6600-50CJ High Performance billet steel oil pump
  • Ford Racing M-9424-M50CJ Cobra Jet tuned intake
  • Ford Racing M-9926-CJ65 throttle body
  • Ford Racing M-9593-LU47 47 lb. fuel injectors
  • Four-valve-per-cylinder BOSS fully CNC ported aluminum heads
  • Roller-finger camshaft followers
  • Ford Racing M-6513-M50BR Boss valve springs
  • Ford Racing M-12A227-CJ13 high RPM pulse ring
  • Ford Racing M-8600-M50BALT alternator and mount
  • Ford Racing M-6P067-M50B blue coil covers
  • Ford Racing M-12405-M50 heat range zero (0) spark
  • Ford Racing M-6731-FL820 oil filter
  • NOTE: Custom PCM calibration required when installing M-6007-A50XS crate engine

Comments


 


 


About the Video

Ford Racing 5.0L Aluminator Crate Engine Build

Check out our YouTube channel for even more tech tips, installation videos, how-tos, and more. The best place to go for anything Mustang related!

Published on 2013-08-10
Ford Racing Performance Parts takes us on a tour of their 5.0L Aluminator crate engine build line in Livonia Michigan. Watch as these motors are built by hand.

M-6007-A50NA 5.0L ALUMINATOR CRATE ENGINE FOR N/A APPLICATIONS
M-6007-A50SC 5.0L ALUMINATOR CRATE ENGINE, SUPERCHARGED APPLICATIONS
M-6007-A50XS 5.0L ALUMINATOR XS
Transcript
[MUSIC PLAYING]

Hey Ford fans. Mike D. here, and your product manager at Ford Racing. We're here at PAS-- Performance Assembly Solutions-- in Livonia, Michigan. We're here to take a behind-the-scenes look at the Coyote Aluminator Engine build. You know, the guys here at PAS have a solid track record of building serious Coyote horsepower. These are the same guys that built the 5.0-liter engines for the 2013 Cobra Jet drag cars. Some of these cards have already running in the high 8s at 150 miles an hour. With me is Mike Robinson, engineering manager at PAS. Mike leads the assembly process that transforms these Coyote Mustang GTs and Boss 5.0-liter engines into the Ford Racing Aluminator NA, Aluminator SC, and the new Cobra Jet-inspired Aluminator XS Crate Engines. Mike, get us started on the crate build. I understand there's basically four areas in the build.

That's correct. The process is broken down into four main areas-- teardown and prep, gauging, assembly, and then the line test.

Now, I know that you guys have really put in a lot of high-tech quality controls. Tell us a little bit about that story.

Sure. The assembly process features an operator touchscreen interface at each station, which integrates a set of live, on-screen work constructions together with an electronic fastening system, an in-process torque to turn verification system, a lead tester, and an end-of-line co-test operation, which verifies rolling torque, oil pressure, and compression.

OK. Good. Now, just like a regular production engine, these things are serialized as well and there's an identity to the engine. Tell us a little about that.

That's correct, Mike. Each engine is serialized with a bar code and a part-type identifier. Well, that bar code is scanned then in each operation, and it's used to define the specific assembly-- or build recipe-- that is required to be completed at each station. Every step of that process is monitored and its recorded in the database and an engine birth/history report can be generated at any time as required.

That's great. Tell you what. Let's head inside and take a look at the line.

Very good.

We start with a factory fresh engine. We disassemble it down to the bare block, which is then inspected, deburred, cleaned in a high-pressure jetwash, and then followed with a rinse with fresh water. We then dry it with compressed air and wipe the bores down with light oil to prevent rust and corrosion. The gauging operation is completed on the block, crank, rods, and pistons. All critical dimensions are measured and clearances calculated and recorded against the engine's serial number on an assembly traveler.

All key features on the rotating group are also measured to ensure they meet specification prior to subassembly.

The factory piston and powdered metal rod is replaced by a Manley H-beam forging also featuring ARP 2000 rod bolts and a Molly forged piston dished for the 9-and-1/2-to-1 application or a flat top for the 11-to-1 application. Main bearings are individually sized to specification. They are then installed into the main caps and the block. The rebalance crankshaft is then installed into place followed by the main bearing caps, ensuring they are placed in the correct positions and orientation.

[BEEP]

The main bearing cap bolts are then installed and tightened in sequence per specification using an electronic torque gun. The torque and angle results for each fastener are recorded into the traceability system.

[BEEP]

A fixture is mounted to the block. The crank is then rotated. Peak breakaway torque as well as average rolling torque are then measured and recorded in the traceability system. The piston and rod assemblies are lubricated with oil, then installed into the block. The connecting rod caps and bolts are then installed. Finally, the rod bolts are then torqued to specification using the electronic torque gun.

After the piston and rod assemblies are installed, the torque-to-turn fixture is once again mounted to the front of the block. The crank is again rotated, and we measure peak breakaway torque and average rolling torque once again. The oil pan, baffle, and gasket, and oil pump pickup tube are then installed followed by the multi-layer steelhead gaskets and, finally, the cylinder heads.

The intake and exhaust camshafts are then lubricated and installed--

Good.

-- followed by the cam caps ensuring the correct placement and orientation.

At the second assembly station, the camshafts and VCT phasers are reinstalled and the engine is timed by aligning the ID marks on the gears with those on the chains. The engine assembly is completed by installing the cam covers, front cover, and intake manifold before proceeding to the end of line test operation.

End-of-line test begins with a coolant cavity leak check. Each engine is tested to verify no leaks are present, and the leak test results are recorded in the database. The engine is then rolled into a cold test stand primed with oil and spun over to verify oil pressure, torque-to-turn, and compression of each cylinder. Before the engine is spun, it is primed for two minutes with heated oil. It is then tested at two different RPMs to verify oil pressure and rolling torque.

Ford Racing has taken the Mustang GT 5.0-liter Coyote engine and created another in a series of Aluminator crate engines built to deliver even more performance in either naturally0aspirated or supercharged form. The 5.0-liter Aluminator NA, SC, and XS engines are built with extreme-duty Manley connecting rods and Mahle pistons designed specifically for high-performance applications. The 5.0-liter Aluminator engines are a direct bolt-in for 2011 to 2014 Mustang GT and are also becoming one of the more popular engine swaps for street rods, vintage muscle cars, or restomods using Ford Racing's 5.0-liter engine controls pack. Go to FordRacingParts.com to find a Ford Racing dealer and learn more about the full lineup of Ford Racing parts.

[MUSIC PLAYING]