Get yourself a new set of pedals for your 79-84 Fox Body Mustang with a set from LatemodelRestoration.com. These pedals replace worn originals and are made from Ford blueprints to exact OE specifications. Easy installation means you can complete your project and be on the road sure footed in no time!
-Fits 1979-84 Mustang Manual except SVO
Worn out, torn and missing brake and clutch pedal pads are a common occurrence in Fox Body Mustangs. Years of hard power shifting and every day wear and tear can really do a number on your pedals. Don't keep using pedals with slippery metal showing through -- LatemodelRestoration.com is proud to offer quality 5.0Resto pedals.
Replacing your missing or worn out clutch and brake pedals is an easy install that will take you less than 10 minutes. Follow along in the video as Jmac shows you how to install a set of new clutch and brake pedals in your project Fox Body Mustang. Increase the pedal contact traction over severely worn pedals with ribbed texture. Fits all 79-93 Mustangs with manual transmissions. Great for dressing up that clutch pedal assembly when doing a 5 speed manual swap in your automatic Fox Body Mustang.
0:00:00 - 0:00:12 Our 5.0Resto pedal pads are direct replacements for the originals and they're even made out of a little bit better material for a longer service life. Installation is simple and can be done with absolutely no tools at all.
0:00:12 - 0:00:27 Well that clutch pedal pad is long gone and our brake pedal pad well it is pretty much looks like crap. Removal is super simple. Just grab ahold of the back of the pad. Lift up the edge and pull it off the middle part of the pedal. Installation is equally as easy.
0:00:27 - 0:00:38 Start one edge in and then work your way around the pad until all the retaining lips are fully seated around the middle part of the pedal.
0:00:38 - 0:00:41 Man looks a whole lot better and installation was super simple. go pick up your new brake and clutch pedal pads at LatemodelRestoration.com and be sure to subscribe to our YouTube channel so you can check out the latest install videos and all things mustangs
Get rid of the worn out high mileage look your accelerator pedal is giving your Fox Body Mustang. This 5.0Resto quality gas pedal is the perfect solution to fix your worn out accelerator pedal. It is made in the USA using Ford's blueprints. It includes a pin and retainer for simple installation -- replaces the pressed pin used on factory pedal.
This is also a great part to replace your thinner automatic accelerator pedal when doing a 5 speed swap on your automatic Mustang.
Don't let your Stang suffer from the ugly gas pedal look -- pick up a 50Resto accelerator pedal today!! Follow along in the video as Jmac shows you how to remove and install an accelerator pedal in your Pony Car.
0:00:01 - 0:00:14 Our 5.0Resto gas/accelerator pedal is injection molded from plastic features the correct curvature for 85-93 manual transmission and has a factory attaching points even includes new attaching hardware.
0:00:14 - 0:00:31 Our test subject here was originally equipped with an automatic transmission but was later converted to a manual 5 speed. Now because of this it has the narrow flat automatic style gas pedal pad. While we wanted to put in the correct 85-93 curved wide accelerator pedal pad.
0:00:31 - 0:01:00 now this can be done in the car but it's a heck of a lot easier if you go ahead and just pull the pedal assembly out and do it on the ground or on the bench. Tools you need for this is a 3/8 ratchet with the small extension in either a 1/2" or 13 mm socket. You also need a flat blade screwdriver and a hammer and small punch to remove the accelerator pedal from the vehicle. Grab your socket and ratchet and remove the two retaining nuts that hold the pedal to the firewall.
0:01:00 - 0:01:17 Helps to have an extra set of hands under the hood holding the throttle wide open so it gives you slack in the throttle cable. now you can take a flat blade screwdriver and pry be cable retainer out of the pedal the factory pedal is held in place with a pressed in spline roll pin.
0:01:17 - 0:01:34 All you have to do is punch the roll pin out of the pedal assembly. Remove the existing pedal. Grab your new pedal and position it. Put in the supplied roll pin and lock it down with the supplied e-clip. Now you ready to put the pedal back in the Mustang.
0:01:34 - 0:01:48 For a minimal investment in time, we now have the correct accelerator pedal pad and while you're on LatemodelRestoration.com don't forget to pick up new breaking clutch pedal pads as well. Also subscribe to our YouTube channel and checkout all of our latest mustang specific videos!
50resto - Dedicated To The Preservation Of The Fox Body Mustang
50resto is your trusted source for 1979-93 Mustang Foxbody restoration products. Buy 50resto products from Latemodel Restoration Supply and receive the best value, quality and industry-leading customer service. Whether you need Fox Body Mustang weatherstrip, headlights, taillights, seals, body panels, hardware, door handles, trim parts, carpeting or upholstery, 50resto is the brand you should demand.
SVE and 50resto Warranty
One Year Hassle Free Replacement
SVE and 50resto products are warranted to be free from defects in materials or workmanship for one year from date of purchase. What does this warranty cover? YOU! That’s right, whether you ordered a SVE brand Mach I grille delete or a 50resto brand light kit, if your product fails within a year of your purchase we got your back! Some conditions will apply.
This is by far the best experience I have ever had buying parts for my mustang. There is no other place for me, then LatemodelResto. I have bought multiple parts over multiple orders and have had nothing but a smile from ear to ear. Aaron Westerman was my contact person from LatemodelResto. I could not ask for a better customer service representative than him! He went above and beyond multiple times for me and made my experience with Latemodel the reason I keep coming back. LatemodelResto will continue being my #1 stop for my Mustang parts.
This is my baby! Betty has 302 and is fun to drive for an automatic! lol. I love her and I'm excited to buy all my parts from Latemodel Restoration to make her faster and even twice as fun for many ye...