Makes Your Mustang's Interior Look & Feel Like New Again!
2003-04 Cobra look for your Fox
Made in the USA
What's in the Box
(1) Driver Seat Back Upholstery
(1) Driver Seat Bottom Upholstery
(1) Passenger Seat Back Upholstery
(1) Passenger Seat Bottom Upholstery
(2) Rear Seat Back Upholstery
(1) Rear Seat Bottom Upholstery
(1) Driver Seat Back Foam
(1) Driver Seat Bottom Foam
(1) Passenger Seat Back Foam
(1) Passenger Seat Bottom Foam
1984-1986 Mustang 2003-04 Cobra Style Sport Seat Uphoslstery
This Mustang Seat Upholstery is intended for the 1984-1986 Mustang Hatchbacks with sport high back front bucket seats. This 2003-04 Cobra Style upholstery features vinyl back & sides with Suede seating surface. Some front seats use a small headrest cover, which is included. GT's with a halo must be reused.
High Quality Vinyl Sport Seat Upholstery for Your Mustang
If the seats in your Mustang have seen better days, a set of new seat upholstery for your Fox body Mustang is just the ticket! Just follow the instructions on our Mustang seat upholstery installation blog by removing the factory seat upholstery/foam and re-cover your Mustang seats with this reproduction kit to make the seats in your Mustang look and feel like new again.
Made From OE Patterns
This 2003-04 Cobra style sport vinyl upholstery kit features OE style patterns to match the seats that your Mustang came with from the factory. It adds a great custom touch to any Fox Mustang.
- Does both front and back seats! Seat Foam replaces Front Seats Only. Rear Seat Foam is Reused.
WarrantyTMI is the only interior manufacturer that offers a Limited Lifetime Warranty. This will cover any workmanship errors caused by the manufacturer and does not cover installation errors or normal wear and tear.
Great upholstery and foam - only a few minor issues
chris c. on
Installed this on my 85/86 seat frames this week. Took the better part of three days to get everything, mostly because I was taking my time.
Good - really nice color and 'strong' feeling upholstery, didn't have any concerns tugging on it to get it to install. - video on YouTube was extremely helpful, especially the tip about using the bags.
Challenges - the knee bolsters assume you are using 87+ seats (even though this part # says 84-86) so the metal piece from the old seats doesn't fit the new foam and plastic mounting bracket. The 85/86 seats have a screw through a pull handle that attaches to the bracket. The new plastic piece assumes the original metal would bolt into it. Had to remove the speed nuts and drill out the plastic big enough to fit the handle and screws from the front - knee bolster bottom needs to be stapled to the plastic, but using industrial staples they push through the upholstery. Had to push the protruding staple down with pliers. - foam on the front seat, upper part needs to be compressed against the frame for any chance of getting the cover on. Once the rods are attached to the foam loops at the top, the whole thing wants to lift off the frame as you tug on it. Ended up zip-tying the rods to the frame (then cut them off when I finally got the J clips to catch.) - I also bought the carpet set from LMR and applied the new carpet when building the rear seats. Despite the video, there was no way to get the push pins to catch on the frame without first stapling the carpet to the frame (I put the latch back in to get it to line up correctly.) I then had to 'notch' the carpet around the push pin holes to get them to push in. Otherwise the carpet was too thick for the push pins to grab. The corners also needed to be trimmed to fit.
Overall, very impressed with the kit and installation, other than the few items I had to engineer around above.
This is by far the best experience I have ever had buying parts for my mustang. There is no other place for me, then LatemodelResto. I have bought multiple parts over multiple orders and have had nothing but a smile from ear to ear. Aaron Westerman was my contact person from LatemodelResto. I could not ask for a better customer service representative than him! He went above and beyond multiple times for me and made my experience with Latemodel the reason I keep coming back. LatemodelResto will continue being my #1 stop for my Mustang parts.
My name is Bryan Bayer and this is my 1988 Mustang GT. Currently going through the process of smoothing the engine bay and building a new motor. Motor is a stock short block 302 with GT40P heads and t...