Tired of spending hours removing pesky molding or decal adhesive? Try the Smart Eraser pad. This handy tool attaches to your drill or grinder and spins away the leftover glue from molding, emblem, or decal removal in a fraction of the time as manual methods without damaging the paint. Includes arbor for use with your 3/8" drill.
Is it time to replace your 5.0 emblem on the side of your Fox Body Mustang? Maybe you have sent your Foxbody off to paint and you aren't sure exactly where the new 50 emblems should go back onto your Mustang. Most people may not realize that these were installed by hand on the Ford assembly line. Unlike later year model Mustangs, these did not use alignment tabs and holes in the fender. Thus making it hard to determine the exact spot these emblems show go back into.
Follow along with Jmac as he shows you how to remove and install new 5.0L Mustang Emblems back into their proper place. The emblem removal process will work on any emblem that is held on with 3M style adhesive tape.
These emblems will fit the following year model Mustang GT LX SVT Cobra: 1979 (79) - 1980 (80) - 1981 (81) - 1982 (82) - 1983 (83) - 1984 (84) - 1985 (85) - 1986 (86) - 1987 (87) - 1988 (88) - 1989 (89) - 1990 (90) - 1991 (91) - 1992 (92) - 1993 (93)
1979 to '93 Mustangs equipped with the five liter engine are also equipped with this chrome five liter fender emblem. Now, if yours looks a little bit like this, it's definitely in the wrong spot. But then again, who's to say what the right spot is? Because the factory really didn't have a template. They just kind of stuck it in a general direction.
But this one needs to be a little bit more centered, a little further up, and definitely more level. Removal of the emblem is pretty simple. Just take some masking tape, and tape around the emblem to protect the paint. Then you can use either fishing string or a putty knife to break the tape loose from the paint.
Once the emblem's out of the way, go ahead and remove your tape, clean up the entire area, and then use an eraser wheel to remove whatever tape residue is left.
Then you can use the template for locating the fender emblem. This can be downloaded off of latemodelrestoration.com's website. Peel and stick.
Now you want to repeat this same process for the other side. And man, that really made a good improvement on this '90 coupe.
Now to grab your set of chrome 5.0 emblems, hop on over to latemodelrestoration.com.
Check out our YouTube channel for even more tech tips, installation videos, how-tos, and more. The best place to go for anything Mustang related!
I was pretty skeptical about this product doing what it was advertised to do but I was pleasantly surprised at how well it worked. I peeled the door moldings off both sides of my 89 vert and tried a few different chemicals to remove the adhesive left behind and nothing worked. I purchased the eraser and it took about 45-60 minutes for each side. Thank you LRS!
Testimonial: Fast, free shipping... need i say more?
This whole year (2013) i've ordered numerous parts. from the front end (core support, head lights, radiator) to a all new rear end ( gears, axles, control arms) and everything in between. very pleased with Latemodel restoration's fast, free shipping and prices. never had any issues with orders i just point,click, and two days later its at my doorstep. you can bet when it warms up, and i get some seat time, ill be back for parts reviews. GREAT JOB LMR! keep up the good work.
My 2011 Mustang has a V-6, but will run with the V-8's. I started out with Roush axle back exhaust, then a Airaid cold air intake, and a bigger throttle body, and recently i got the Bama tuner, I have...