If you are re-painting your Fox Body Mustang, the best way to get a quality paint job is to take off the Body Side Moldings to get proper coverage. These moldings are the pieces that run along each side of the body and attach to the doors, fenders, and rear quarter panel. They typically get pitted and severely faded due to exposure to the elements. LRS carries all of the new body side moldings that are available for 1985-1986 Fox Body Mustangs. This is the RH rear quarter panel molding that fits behind the rear wheel in front of the bumper. This molding is made of hard plastic and attaches via plastic studs that stick through the body panel and are held in place with pal nuts. This molding fits all 1985-1986 Mustang LX Coupe, Hatchback , & Convertible Models. Moldings are molded in black plastic and is ready for prep and paint. Moldings are Sold individually and must be Painted to match.
Are your Mustang side body moldings peeling away from your Mustang or looking a little wavy? Worse yet are you missing pieces of our Mustang body side moldings? If so, no worries. Here at LatemodelRestoration.com we have plenty of Mustang Body Moldings to get your Fox Body Mustang looking great in no time. We carry body moldings for LX, GT and Cobra models ranging from 1985-93 year ranges.
Watch the video and follow along as Jmac walks you through installing a set of body moldings on a LX Fox Body Mustang Coupe. Jmac goes through the process of removing your old moldings and the how to remove the adhesive left behind on the Mustang. So whether your are doing an installation or just need help on removing your FoxBody Mustang Body Moldings here at Latemodel Restoration we have you covered with plenty of Mustang tech.
Get your Project FoxBody Mustang performing and looking great LatemodelRestoration.com's 5.0Resto and SVE brand Mustang Restoration Parts.
JONATHAN MCDONALD: Luckily, we here at latemodelrestoration.com have you covered with all-new LX body side moldings. They're available individually as well as in several different kits for your '87 to '93 LX Mustang. The kit we have in front of us is intended for 1987 and 1990 LX Mustangs. We also have a kit available for '91 to '93 LX Mustangs. These complete kits include the six urethane pieces as well as the four plastic pieces.
Now, if your car is like most others, the urethane pieces are the main offenders. And we have a six-piece kit that covers all those urethane pieces. It'll fit '87 all the way to '93. All these kits include the 3M adhesion promoter. That way, you don't have to worry about them peeling off.
Now for the question of color-- 1987 to 1991 LX Mustangs are going to have trim-black painted molding. 1992 and '93 Mustangs-- those are going to be body color. So you're going to want to visit your body shop to have those matched up to your car.
The urethane body side moldings used on Fox Mustangs is prone to curling, peeling tape, and even some shrinkage, especially if your car's been painted or the moldings have been removed and not reinstalled properly. A walk around this 1990 LX coupe shows us that several of the moldings, both urethane and plastic, need some love. And we're going to give them just that.
Removal of your body side moldings, especially the urethane ones, is pretty straightforward. If you're going to be reusing moldings, you can use either fishing string or a really thin-bladed putty knife. That way, you don't damage your molding. If you're in a situation like us where you're replacing the molding, simply grab hold and tear it off.
Your six urethane body side moldings are attached to the car using 3M double-sided tape. And whenever you pull your old molding off, there's going to be some residue left behind, maybe even some tape remnants. And we're going to need to clean that up.
First thing to do is wipe off any dirt that's behind that molding. Then you can grab one of our eraser wheels, available on our website, to remove any of the leftover tape residue. After you get that extra tape residue out of the way, I like to go ahead and wipe down what denatured alcohol just to make sure there's no contaminants left on the surface. After we're done with that, we'll go ahead and use the 3M adhesion promoter included with our molding kits. That way, you don't have to worry about that tape peeling off later down the road.
After you get your paint prepped up, then go ahead and grab your fresh molding. Then go ahead and pull back the corners of the tape like this. And then use masking tape to center the molding onto the car before you peel the tape off and stick it permanently.
Now, if you find yourself in the same position we did, missing a plastic molding, don't worry. We've got you covered. And you even have the correct attaching nuts that have the proper sealer on them to get it to attach back to the body.
To install, you'll have to remove your inner trunk panels. Slide the plastic molding into place. And then use a 1/2-inch wrench to tighten down your three nuts.
Now, your front fender molding is plastic, just like the rear of rear quarter molding. And it's held on with four nuts, the exact same nuts like the rear quarter. And you can access those from underneath the bumper cover right here using the exact same 1/2-inch wrench.
It is amazing what you can accomplish with just a few new moldings and a can of exterior trim paint. To improve the appearance of your Mustang, check out latemodelrestoration.com.
Check out our YouTube channel for even more tech tips, installation videos, how-tos, and more. The best place to go for anything Mustang related!
This piece was the only one I was missing and it was specific to 85-86 GT models and I couldnt find one at a junkyard so I bought it off of here, Ordered it at 12 a.m on a Saturday and they got the order printed off and was shipped on Monday and got to me that following Tuesday. Awesome. Only promblem I had was they dont include an adhesive or clips which they should offer. Other than that it was awesome..
We do offer the attaching hardware under part # PE-1073
50resto - Dedicated To The Preservation Of The Fox Body Mustang
50resto is your trusted source for 1979-93 Mustang Foxbody restoration products. Buy 50resto products from Latemodel Restoration Supply and receive the best value, quality and industry-leading customer service. Whether you need Fox Body Mustang weatherstrip, headlights, taillights, seals, body panels, hardware, door handles, trim parts, carpeting or upholstery, 50resto is the brand you should demand.
SVE and 50resto Warranty
One Year Hassle Free Replacement
SVE and 50resto products are warranted to be free from defects in materials or workmanship for one year from date of purchase. What does this warranty cover? YOU! That’s right, whether you ordered a SVE brand Mach I grille delete or a 50resto brand light kit, if your product fails within a year of your purchase we got your back! Some conditions will apply.
I would like to give a big thank you to Latemodel Resto Employee Tyler Rodriguez, he went above and beyond to provide outstanding Customer service, really made me a customer for life, i plan to make all my future purchases from latemodelresto when i get my hands on a 2015 Mustang. thanks again Tyler for the outstanding customer service you and latemodelresto provide.