The 94-04 Mustang Door Panel Inserts, also known as Mustang Door Handle Cup, are notorious for breaking, fading and peeling. The door inserts are handled every time you close and open the door so they get a ton of wear and tear. Follow along in the video as Jmac shows you how to remove/install a 94-04 Mustang door panel insert door panel cup.
Our 94-04 Mustang Door Panel Inserts are available in both black and charcoal colors. We have Ford Original (OEM) and aftermarket panels. If you need these to match your parchment (tan) interior you will need to paint them.
Don't forget to replace those broken and faded Mustang Power Window Switches while changing out the door panel insert.
These door panel inserts fit the following year model Mustangs: 1994 (94) - 1995 (95) - 1996 (96) - 1997 (97) - 1998 (98) - 1999 (99) - 2000 (00) - 2001 (01) - 2002 (02) - 2003 (03) - 2004 (04)
These door panel inserts fit the following Mustang models: GT, V6, Cobra, Bullitt and Mach 1
1994 to 2004 Mustangs are notorious for having broken door panel inserts. Replacing them is super easy and takes just a few minutes of your time.
To remove year old one, start at the top here. Push down and pull out. Relieve that top clip. Pull up on the front, and then release the clip back here at the back just by pulling up.
Then you can pull your wiring harness out a little bit, grab your flat blade screwdriver, and remove the connector for your power mirror switch. Then grab you a Phillips head, and remove the two screws holding the switch panel to the door panel insert.
The switch panel comes free. Now you've got two tabs that hold this power mirror switch into place. You're going to have to press both of them in and try and shove it out at the same time. It will take a little bit of effort to get it free. It'll snap out.
Then you can grab your new door panel insert. Now this is a direct fit for '94 to '98 because it's already black. If you've got a '94 to '04, you will need to paint it.
Snap your mirror switch back into place. Engage your door lock switches. Finger start your two screws. Then take your Phillips screwdriver, and tighten them down. You don't want to over tighten them because you don't want to break your new bezel.
Then you can plug in your power mirror switch. And your new bezel comes with a new clip, so you don't have to transfer the old one.
To reinstall, slide your switch all the way up into place. Engage the back of the insert, and slide the clip into place. And then engage your top clip, and you're done.
Now again, '99 to '04, you will have to paint it. Now for the correct interior color, go to our website, check out our interior paint and dye section. Once you find the correct color for your car, click on the video and watch how to paint the plastic and vinyl interior trim parts.
Now for more interior restoration tips, check out latemodelrestoration.com.
Check out our YouTube channel for even more tech tips, installation videos, how-tos, and more. The best place to go for anything Mustang related!
Ford Motor Company Genuine Parts, Motorcraft® Parts and Ford and Motorcraft Remanufactured Parts are all excellent choices when it comes to performance, longevity and value for your Mustang or SVT Lightning. And they’re all backed by a Ford Motor Company limited parts warranty*, so you know their parts you use are going to perform like they should. Put the same parts on your Lighting & Mustang that came from the factory!
Had a problem with an order/quality issue. I put up a review stating so, and was contacted by Mike Linley, who was soooo nice and sooo professional, I almost felt bad about my review !! I felt the review was necessary because of bad welds/paint. Mike explained that they had a particular issue with that supplier and they had changed suppliers because of it. I must have mistakenly got an old set. (upper/lower Control arms-Foxbody). Mike asked a few questions, and was Sending me an updated replacement set while we were on the phone.!!! This is what I wish all Vendors would do; no arguments, no blame, no B.S. !! This is why LateModel stands out as an upstanding company, and backs up their products with AWESOME Customer service. Very rare in this day and age, and because of this I will be a customer for life, and will spread the good word ! Great to know some honest and Classy companies still operate in the good ol' USA. Thanks LateModel, and Thanks Mike !!! I look forward to seeing the New LCA'S and will review them too...You guys did the right thing and should and I'm overly impressed!