This great looking Honeycomb Trim Panel Decklid Insert is available for 99-04 Mustangs and was made specifically for Mach 1 Mustangs. Parts consist of 3-piece black honeycomb panel. (For each trim panel you will be removing your factory GT/Mach 1 and Ford oval emblems and reusing the Ford emblem. Panel comes with new black Mach 1 emblem pre-installed)
All trim panels come standard with the appropriate cut out so no modifications are necessary. This injected molded plastic is applied between the taillights in approximately 30 minutes. No drilling required just simply applies with 3M 2-way Acrylic Bonding Tape.
I installed this kit yesterday and was over all very pleased!. Some SLIGHT fitment issues and was a little tricky to line up to do lack of molded in alignment pegs or anything. But If you take your time and measure everything and have a careful eye then you should have a problem.
Did the entire job in about a half hour , removed license plate , used heat gun to warm GT and ford emblems and removed them. Cleaned everything real well with rubbing alcohol. Removed 3M tape liner from the panels and installed them one by one.
End result was that is completely changed the look of the rear of my car and was a awesome addition to my Mach1 conversion!.
Good quality materials, the 3M backing tape is VERY sticky and has a good immediate bond.
Price is a bit steep for just some plastic but otherwise completely satisfied!.
I would for sure recommend this to anyone!.
Yes, I would recommend this item to a friend!
Was this review helpful to you?
Jorge C. on
I bought the honeycomb inserts but plastic looks cheap. Looks great on the car but I personally don't think is worth the price it sells for. And plus 3m tape to secure to your trunk didn't like that either.
Was this review helpful to you?
Jerrod D. on
Fits and looks great and installation went smooth. A little pricey for just some plastic but otherwise very satisfied!.
Classic Design Concepts - Where Styling Meets the Road
Classic Design Concepts has been on of the top leaders in the industry of designing and manufacturing quality restyling components since 1990. Using OE certified materials and manufacturing procedures that meet or exceed OE standards, CDC’s classic restyling designs have factory fit and finish. Classic Design Concepts, LLC creates excitement that enhances the flow of natural lines of your Mustang, while using factory mounting points and hardware to ease installation and ensure proper tolerances. CDC is a TS certified company providing the enthusiast and Original Equipment manufacturers with cutting edge style and unsurpassed quality.
Get your Mustang looking great with CDC's wide selection of billet grilles, trunk panel inserts, light bars, window louvers, chin spoilers, and ram air hood systems at Latemodel Restoration.
Products by Vehicle
Upload a Picture
Upload your own picture of the Mustang Mach 1 Honeycomb Trunk/Decklid Panel (99-04)
Please make sure to hold your device horzonally (like a camera) rather than vertical (like a phone).
By uploading an image, you agree to give LatemodelRestoration.com permission to use it in future advertisements and promotions.
Had a problem with an order/quality issue. I put up a review stating so, and was contacted by Mike Linley, who was soooo nice and sooo professional, I almost felt bad about my review !! I felt the review was necessary because of bad welds/paint. Mike explained that they had a particular issue with that supplier and they had changed suppliers because of it. I must have mistakenly got an old set. (upper/lower Control arms-Foxbody). Mike asked a few questions, and was Sending me an updated replacement set while we were on the phone.!!! This is what I wish all Vendors would do; no arguments, no blame, no B.S. !! This is why LateModel stands out as an upstanding company, and backs up their products with AWESOME Customer service. Very rare in this day and age, and because of this I will be a customer for life, and will spread the good word ! Great to know some honest and Classy companies still operate in the good ol' USA. Thanks LateModel, and Thanks Mike !!! I look forward to seeing the New LCA'S and will review them too...You guys did the right thing and should and I'm overly impressed!